1. Set the size of the artboard.
2. Switch on crop marks and decide on their locations.
3. Create the data for printing and cutting inside the crop marks.
4. Perform printing using the printer.
5. Load the printed media on the cutting machine.
6. Output the paths (cutting data) to the cutting machine.
   The crop marks are detected, then cutting starts.

 Set the size of the artboard

1. From the [File] menu, click [Document Setup].
   The [Document Setup] dialog box appears.



2. Make the settings for the size of the media to use for printing and cutting.

 Crop-mark settings

1. Click to select it.
   Crop marks display on the artboard.



2. Click the arrow at the upper right of the palette, then click [Crop-mark Locations].
   The [Crop-mark Locations] dialog box appears.



3. Take into account the margins that are required when cutting the media and make the settings for the locations of the crop marks accordingly.
   
   If you're performing cutting using the GX-640/500/400/300, make the following settings for the printing margins.
   
   
   • Top: 30 mm or more
   • Bottom: 30 mm or more
   • Left: 10 mm or more (*)
   • Right: 10 mm or more (*)
   
   *: When you're using lengthy media having a large amount of feed, we recommend providing left and right margins of about 25 millimeters each.
   
   At this time, enter the following settings or calculated values for the crop-mark locations.
   
   
   • W = (media width) - (left and right margins) - 20 mm
   • L = (media length) - (top and bottom margins) - 20 mm
   • X = (left margin)
   • Y = (bottom margin)
   
   
   If you're performing cutting on the GX-24/GS-24, enter the following values.
   
   

   [cropmark : 3 points]

   Size	Crop-mark locations
   A4 portrait	X: 15 mm, Y: 20 mm  W: 170 mm, L: 210 mm
   A4 landscape	X: 30 mm, Y: 20 mm  W: 240 mm, L: 120 mm
   A3 portrait	X: 30 mm, Y: 20 mm  W: 240 mm, L: 330 mm
   A3 landscape	X: 15 mm, Y: 20 mm  W: 380 mm, L: 205 mm
   B4 portrait	X: 15 mm, Y: 20 mm  W: 215 mm, L: 275 mm
   B4 landscape	X: 15 mm, Y: 20 mm  W: 325 mm, L: 170 mm




[cropmark : 4 points]

Size	Crop-mark locations
A4 portrait	X: 10 mm, Y: 20 mm  W: 170 mm, L: 200 mm
A4 landscape	X: 30 mm, Y: 20 mm  W: 230 mm, L: 110 mm
A3 portrait	X: 30 mm, Y: 20 mm  W: 230 mm, L: 320 mm
A3 landscape	X: 15 mm, Y: 20 mm  W: 370 mm, L: 195 mm
B4 portrait	X: 15 mm, Y: 20 mm  W: 205 mm, L: 265 mm
B4 landscape	X: 15 mm, Y: 20 mm  W: 315 mm, L: 160 mm

 Create the data for printing and cutting

 Perform printing on the printer, then cut the printed media

1. Load the media to print on the printer.
   For information on how to perform loading, refer to the user's manual for the printer.



2. Go to the [File] menu and click [Print].
   The [Print] dialog box appears.



3. Make sure the printer to use for printing is selected, then click [OK].
   If enlarged/reduced printing is selected (on), then clear the selection. Perform printing at a scale of 100%.
   The printing data is sent to the printer and printing starts.
   (At this time, do not output the cutting lines.)
   



4. After printing has finished, load the media on the cutting machine.
   Perform setup if the model you're using requires it.
   Load the media so that the three crop marks are positioned as shown in the figure with respect to the cutting machine.
   The orientation of the media must not be changed when you load it.
   



5. Click
   (At this time, output the cutting lines only.)
   The [CutStudio Output] dialog box appears.



6. Select the cutting machine to use for cutting, then click [Cut].
   The cutting data is sent to the machine and cutting starts.