| 
| 
| 
|
| EGX-360 | EGX-300 | EGX-30 | EGX-20 |
INDEX
Common FAQs and Videos:
- PIT Utility: support_pit.phtml
- ADA Braille: workbench_braille.phtml
- Warranty Info: support_warranty.phtml
- Fonts Workbench: workbench_fonts.phtml
- Bed Leveling Kit: faq_bed_level.phtml
- Braille Workbench: workbench_braille.phtml
- Hold-Down Material: faq_multimat.phtml
- Engravers Workbench: workbench_engravers.phtml
- Rhinestone Workbench: workbench_rhinestone.phtml
- Engraving Dictionary: workbench_gravers.phtml
- Educational Workbench: workbench_edu.phtml
- ChipSys Removal System: faq_chipsys.phtml
- RWear Studio Application: support_rwear_studio.phtml
- Roland Jewellers Workbench: workbench_jewelers.phtml
- Graver (Cutting Tool) Workbench: workbench_gravers.phtml
- Dr. Engrave Multiple Cutting Process: support_dr_engrave.phtml
| 
| 
| 
| 
| 
| 
| 
| 
| 
|
| EGX Vise Sales | Color Fill | Rotary Engraving | General Engraving | Engraving For Profit | USB/Vista Install | EngraveLab/ Braille | Cancel a Job | Engraving Sheet | Engraver Roster 2005 |
| 
| 
| 
| 
| 
| 
|
| ZB-20 Install | EGX Accessories | Cut Out Letters Video | Medalion Video | Pen Video | Pin Jig Video | Ruler Video |
| 
| 
| 
| 
| 
| 
| 
|
| ADA Brief | Braille/ EngraveLab | EGX ADA Sign Creation | Power Save Failure | EGX Rhinestone | Indoor ADA | Engrave Studio Vectorizing | Dr. Engrave Vectorizing |
EGX-360 FAQs and Videos:
| 
| 
| 
| 
| 
| 
| 
| 
|
| EGX-360 Brochure | EGX-360 Engrave Guide | EGX-360 FAQ English | EGX-360 FAQ Spanish | EGX-360 Prod Info English | EGX-360 Prod Info Spanish | EGX-360 Specs | EGX-360 Startup | EGX-360 Page Ad |
| 
| 
| 
| 
| 
|
| EGX-360 Setup Guide | EGX-360 Inside Rings Video | EGX-360 Outside Rings Video | EGX-360 Mother of Pearl Video | EGX-360 Rotary OK Video | EGX-360 Water Flow Video |
| 
| 
| 
|
| Slot Table Install | EGX-360 Glass Screens | EGX-360 Glass Tutorial 1 | EGX-360 Glass Tutorial 2 |
EGX-300 FAQs and Videos: (legacy machine)
| 
| 
| 
| 
| 
|
| EGX-300/30 Brochure | EGX-300 Quick Start | MV-2 Vise Video | Diamond Grave Video | Plastic Engr. Video | Ikonics Engraving |
EGX-30 FAQs and Videos: (legacy machine)
| 
| 
| 
| 
| 
| 
|
| EGX-300/30 Brochure | EGX-30 FAQ | EGX-30 Intro Info | EGX-30 Limit Switch | EGX-30 Hardware Setup | EGX-30A Diamond Scribe | EGX-30A Plastic Engraving |
|
| EGX-30 Diamond Grave |
EGX-20 FAQs and Videos:
| 
| 
| 
| 
| 
| 
| 
|
| EGX-20 Brochure | EGX-20 Diamond Drag | EGX-20 Hardware Setup | EGX-20 Job Cancel | EGX-20 Overview | EGX-20 Scribe Video | EGX-20 Plastic Video | EGX-20 Vise Video |
Special Notes on Common Problems:
- The most common problem with using Serial/Parallel on the EGX-20, EGX-30, EGX-300, EGX-400, EGX-600 is when using serial communication the flow control is set to "none". This causes the machine to lose X/Y position control after starting the job. Please ensure this is set to "hardware" flow control.
- The most common problem with using the EGX-300 is that the machine Z1 and Z2 are over-ridden by software settings in the print driver. Set the Z0 on the machine and then set Z1/Z2 in the print driver. Z1 must be less than Z0, and Z2 must be above Z0.
- The most common service issue is Z-motor burnout due to jobs being stopped with the emergency switch on the front of the machine, but without clearing the print buffer. This leaves the job with data on the computer, and when the engraver is powered back on again the residual data flows in at a random Z-height. In the worst case, the head gets driven towards the table and the motor gets overstressed.
